Extreme Drywall handles residential drywall in Central Florida for homeowners, home builders and owner-builders. We hang, tape, finish and texture drywall in new construction homes, room additions, garage conversions and gut remodels, and we take each house from bare framing to walls that are ready for paint. If your project is a full room or larger, our crew is set up for it.
Most Central Florida homes have concrete block exterior walls, with drywall hung on furring strips over the block and on wood studs for the interior walls. Both need a straight, consistent surface before the board goes up, and we check the furring and framing for high and low spots before we hang. Humidity matters here too, so bathrooms, laundry rooms and areas near exterior doors get moisture-resistant board, and the wall and ceiling between the garage and the house get 5/8-inch Type X.
On a new home, drywall is one of the biggest steps between framing and finishes, and it sets the pace for every trade after it. We start once framing and insulation inspections pass, stock the board room by room, and hang full-length sheets to keep butt joints out of the middle of walls. Builders get a crew that keeps to the schedule, and homeowners get walls and ceilings that look clean under the final paint.
An addition has to look like it was always part of the house. We match the existing texture, the corner style and the ceiling finish so the new space blends with the original rooms. On gut remodels, where walls come back to studs, we replace the drywall throughout and finish it to one consistent standard, which often looks better than the house did when it was new.
Florida homes carry a lot of detail work : vaulted and tray ceilings, plant shelves, wall niches and bullnose corners. Each one adds angles and edges that show every flaw if they are rushed. We hang ceilings with drywall lifts, set corner bead straight and plumb, and finish every inside angle so lines stay crisp under paint.
Whether your home calls for smooth walls or a knockdown texture, the finish starts with flat seams. We apply each coat of joint compound wider than the last, sand between coats, and check the surface under raking light before texture or primer goes on. For smooth walls under semi-gloss or in bright rooms, we recommend a Level 5 skim coat.
Tell us about your project and we will follow up with a straightforward estimate.
Free Estimate

Complete drywall packages for new homes, additions and commercial spaces. We take the job from board takeoff through hanging, taping and finishing, with one crew responsible for every wall.

Sheet installation on wood or metal studs and ceiling joists. Full-length 4x12 sheets where the layout allows, fewer butt joints, and a tight screw pattern.

Paper tape bedded in joint compound on every seam, corner bead on outside corners, and setting compound where strength and speed matter.

Coats feathered wide and sanded smooth to a Level 4 or Level 5 finish, then checked under raking light before paint.

Knockdown, orange peel and skip trowel applied across whole rooms and whole houses, or a smooth wall if that is the look you want.

Flat, vaulted and tray ceilings hung with drywall lifts, fastened to the joists and finished so seams stay hidden under overhead light.

5/8-inch Type X board and sound-control wall and ceiling assemblies for multifamily, office and commercial spaces, installed to the project's design documents.

Drywall for offices, retail, multifamily and tenant build-outs, scheduled around the general contractor and the other trades.
FAQ
Both. We work directly with homeowners on additions and remodels, and with home builders and owner-builders on new construction.
Yes. We match knockdown, orange peel and skip trowel textures so an addition or remodeled room blends with the rest of the house.
That wall, and the ceiling if there is living space above, gets 5/8-inch Type X fire-rated board, as the building code requires for fire separation.
It depends on the size of the house, ceiling heights and the finish level, along with drying time between coats in Florida’s humidity. We give you a timeline with your estimate so you can schedule the painters and other trades.
No. We focus on full rooms, additions and whole houses. For a single hole or small patch, a local handyman is usually the better fit.
Call (407) 668-1818 or send your plans or room measurements through the form. We will price the job and send a written estimate, no obligation.
▲ Google Reviews
★★★★★
Where We Work
We work on homes across Central Florida, from Orlando and the surrounding counties to Daytona Beach and the Space Coast, and take larger projects in Tampa Bay, Sarasota, Fort Myers and Jacksonville. View our service area
Tell us about your project and we will follow up with a straightforward estimate.
Get Started
Building, adding on or remodeling? Call (407) 668-1818 or fill out the form to request a residential drywall estimate, no obligation. Contact us.
Free Estimate